XPO 2 mm

Quiet and resilient: a powerful solution for wood flooring and laminate flooring
The SELITPRO® XPO 2 mm is a true all-rounder for a high level of living comfort. Made from high-performance polyolefin foam, it reliably protects your floor from damage caused by heavy loads. In addition, it reduces walking and impact sound and, thanks to its flexible foam structure, compensates for small areas of unevenness.

Great room acoustics thanks to peak values in walking sound

  • Ideal on existing underfloor heating
  • Excellent walking sound reduction
  • Ideal reduction of impact sound in adjacent rooms
Order number70710
Thickness2 mm
Dimensions1 x 10 m
Package contents10 m²
Why XPO 2 mm

Easy to process

Easy to cut
due to printed grid

Protects the floor from damage

Protection against
loads and use

Protection against
falling objects

Protection in
uneven areas

Increases living comfort

Suitability for
underfloor heating*

Reduction of
walking sound

Reduction of
impact sound

Installing XPO 2 mm –

a step-by-step guide

Before installation, please note: Check the base in accordance with CEN/TS 14472 and ensure that the quality of the base is suitable for proper processing. In general, the base should be clean, level, dry, resistant to tension and compression and should not contain any substances such as plasticisers, solvents or other diffusing substances. It must be ensured that the base is in a state of equilibrium humidity and that the CM value is below 2.0 % (for cement screed) or below 0.5 % (for anhydrite screed and anhydrite flowing screed). The processing instructions of the flooring manufacturer are to be observed as binding specifications.

Cleaning the surface

Cleaning the surface

Step 1
Clean the surface thoroughly with a brush or vacuum cleaner. Remove any adhesive and paint residues completely.

Applying the moisture protection

Applying the moisture protection

Step 2
Mineral bases need protection against rising moisture. Cover the room completely with SELITstop® Comfort Vapour Barrier. Allow the joints to overlap by approx. 5 cm and seal them in a vapour-tight manner with SELITstop® Aluminium-Foil Sealing Tape.

Masking the wall connection area

Masking the wall connection area

Step 3
In the wall connection area, place the film in a trough-like position at approx. 3-4 cm to protect against moisture and fix to the wall with SELITstop® Aluminium-Foil Sealing Tape. Alternatively, use SELITstop® Moulding Protection Belt. In this case, install the moisture protection film flush with the wall.

Laying out the first panel

Laying out the first panel

Step 4
Lay the first panel of the underlay flush with the wall over the entire width of the room.

Installing the flooring

Installing the flooring

Step 5
Lay the flooring in the same orientation as the underlay. Do not place any weight on the underlay, if necessary place the panel under your knees/feet to distribute the load.

Finishing the installation

Finishing the installation

Step 6
Repeat steps 4 to 5 until the flooring has been installed throughout the entire room.

Technical data (according to EN 16354)
Punctual conformability (PC)up to 1 mm
Compressive strength (CS)≥ 120 kPa
Compressive creep (CC)≥ 25 kPa
Dynamic load (DL25)≥ 1,000,000 cycles
Resistance to large ball (RLB)≥ 120 cm
Water vapour diffusion resistance (SD)
Thermal resistance (R)∼ 0.04 m²K/W
Impact sound reduction (IS)up to 20 dB
Reaction to fire (RTF)Efl
*Suitability for underfloor heatingYes, if flooring R ≤ 0.11 m2K/W (e.g. laminate up to approx. 12 mm, wood flooring up to approx. 14 mm)

Meets the increased requirements of the EPLF and MMFA (Group 1)


SELITPRO XPO 2 mm Produktinformationsblatt
Size: 1,4 MB
SELIT Catalogue 2021
Size: 7,8 MB
Excellent quality
Made in Germany.

Emissions-tested: A+

In accordance with the French VOC regulations, our underlays achieve the lowest emission values and therefore feature the A+ mark.
Learn more

Approved by the building authorities

Stay on the safe side with SELIT: all our underlays are approved by the building authorities.
Learn more