2.2 mm

First choice for a low installation height
Do you not have much vertical space to play with? The SELITAC® 2.2 mm is ideally suited for low installation heights. Thanks to its slim design, it reliably protects your floor from heavy loads and damage from falling objects. It also reduces footfall and walking sound for greater living comfort.

Polystyrene foam with high level of compressive strength – for low installation heights

  • High load-bearing capacity
  • Reduction of walking and impact sound
  • Suitable for underfloor heating
Order number70678
Thickness2.2 mm
Dimensions1 x 25 m
Package contents25 m²
Why 2.2 mm

Easy to process

Easy to cut
due to printed grid

Protects the floor from damage

Protection against
loads and use

Protection against
falling objects

Protection in
uneven areas

Increases living comfort

Suitability for
underfloor heating*

Reduction of
walking sound

Reduction of
impact sound

Installing 2.2 mm –

a step-by-step guide

Before installation, please note: Check the base in accordance with CEN/TS 14472 and ensure that the quality of the base is suitable for proper processing. In general, the base should be clean, level, dry, resistant to tension and compression and should not contain any substances such as plasticisers, solvents or other diffusing substances. It must be ensured that the base is in a state of equilibrium humidity and that the CM value is below 2.0 % (for cement screed) or below 0.5 % (for anhydrite screed and anhydrite flowing screed). The processing instructions of the flooring manufacturer are to be observed as binding specifications.

Cleaning the surface

Cleaning the surface

Step 1
Clean the surface thoroughly with a brush or vacuum cleaner. Remove any adhesive and paint residues completely.

Applying the moisture protection

Applying the moisture protection

Step 2
Mineral bases need protection against rising moisture. Cover the room completely with SELITstop® Comfort Vapour Barrier. Allow the joints to overlap by approx. 5 cm and seal them in a vapour-tight manner with SELITstop® Aluminium-Foil Sealing Tape.

Masking the wall connection area

Masking the wall connection area

Step 3
In the wall connection area, place the film in a trough-like position at approx. 3-4 cm to protect against moisture and fix to the wall with SELITstop® Aluminium-Foil Sealing Tape. Alternatively, use SELITstop® Moulding Protection Belt. In this case, install the moisture protection film flush with the wall.

Laying out the first panel

Laying out the first panel

Step 4
Lay the first panel of the underlay flush with the wall over the entire width of the room with the cutting grid facing upwards.

Installing the flooring

Installing the flooring

Step 5
Lay the flooring in the same orientation as the underlay. Do not place any load on the underlay. If necessary, place the board under your knees/feet to distribute the load.

Finishing the installation

Finishing the installation

Step 6
Repeat steps 4 – 5 until the entire floor has been installed.

Technical data (according to EN 16354)
Punctual conformability (PC)up to 1 mm
Compressive strength (CS)≥ 90 kPa
Compressive creep (CC)≥ 25 kPa
Dynamic load (DL25)≥ 250,000 cycles
Resistance to large ball (RLB)≥ 120 cm
Water vapour diffusion resistance (SD)
Thermal resistance (R)∼ 0.07 m²K/W
Impact sound reduction (IS)up to 20 dB
Reaction to fire (RTF)Efl
*Suitability for underfloor heatingYes, if flooring R ≤ 0.08 m²K/W (e.g. laminate up to approx. 10mm, wood flooring up to approx. 12 mm)

Meets the increased requirements of the EPLF and MMFA (Group 1)

Downloads

SELITAC 2,2 mm Produktinformationsblatt
Size: 1,9 MB
Catalogue 2020
Size: 64,9 MB
Excellent quality
Made in Germany.

Emissions-tested: A+

In accordance with the French VOC regulations, our underlays achieve the lowest emission values and therefore feature the A+ mark.
Learn more

Approved by the building authorities

Stay on the safe side with SELIT: all our underlays are approved by the building authorities.
Learn more